# ------------------------------------------------------------------------------
# tlp - Parameters for power save
 
# Hint: some features are disabled by default, remove the leading # to enable them
 
# Set to 0 to disable/1 to enable TLP
TLP_ENABLE=1
 
# Seconds laptop mode has to to wait after the disk goes idle before doing a sync.
# Non-zero value enables, zero disables laptop mode.
DISK_IDLE_SECS_ON_AC=0
DISK_IDLE_SECS_ON_BAT=2
 
# Dirty page values (timeouts in secs).
MAX_LOST_WORK_SECS_ON_AC=15
MAX_LOST_WORK_SECS_ON_BAT=60

# Select a cpu frequency scaling governor: ondemand/powersave/performance/conservative
# Important:  
# - You *must* disable your distribution's governor settings or conflicts will occur
# - ondemand is sufficient for *almost all* workloads, you should know what you're doing!
#CPU_SCALING_GOVERNOR_ON_AC=ondemand
#CPU_SCALING_GOVERNOR_ON_BAT=ondemand

# Set the min/max frequency available for the scaling governor.
# Possible values strongly depend on your cpu. For available frequencies see 
# tlp-stat output, Section "+++ Processor".
# Hint: Parameters are disabled by default, remove the leading # to enable them,
#       otherwise kernel default values are used.
#CPU_SCALING_MIN_FREQ_ON_AC=0
#CPU_SCALING_MAX_FREQ_ON_AC=0
#CPU_SCALING_MIN_FREQ_ON_BAT=0
#CPU_SCALING_MAX_FREQ_ON_BAT=0

# Minimize number of used cpu cores/hyper-threads under light load conditions
SCHED_POWERSAVE_ON_AC=0
SCHED_POWERSAVE_ON_BAT=1

# Kernel NMI Watchdog
# 0=disable (default, saves power) / 1=enable (for kernel debugging only)
NMI_WATCHDOG=0
        
# Change CPU voltages aka "undervolting" - Kernel with PHC patch required
# Freq:voltage pairs are written to /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
# CAUTION: only use this, if you thoroughly understand what you are doing!
#PHC_CONTROLS="F:V F:V F:V F:V"
 
# Hard disk devices, separate multiple devices with spaces (default: sda).
# Devices can be specified by disk id too (lookup with: tlp diskid).
DISK_DEVICES="sda sdb"

# Hard disk advanced power management level: 1(max saving)..254(off)
# Levels 1..127 spin down the disk.
# Separate values for multiple devices with spaces.
DISK_APM_LEVEL_ON_AC="254 254"
DISK_APM_LEVEL_ON_BAT="128 128"

# Hard disk spin down timeout:
# 0:        spin down disabled
# 1..240:   timeouts from 5s to 20min (in units of 5s)
# 241..251: timeouts from 30min to 5.5 hours (in units of 30min)
# (see 'man hdparm' for details)
#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"

# Select i/o scheduler for the disk devices - possible values are 
#   noop anticipatory deadline cfq (Default: cfq) 
# Separate values for multiple devices with spaces.
#DISK_IOSCHED="deadline cfq"
 
# SATA aggressive link power management (ALPM):
# min_power/medium_power/max_performance
SATA_LINKPWR_ON_AC=max_performance
SATA_LINKPWR_ON_BAT=min_power

# PCI Express Active State Power Management (PCIe ASPM):
# default/performance/powersave
# Hint: needs kernel boot option pcie_aspm=force on some machines 
PCIE_ASPM_ON_AC=performance
PCIE_ASPM_ON_BAT=powersave

# Radeon graphics clock speed (profile method): low/mid/high/auto/default
# auto = mid on BAT, high on AC; default = use hardware defaults
# (Kernel >= 2.6.35 only, not with fglrx driver!)
RADEON_POWER_PROFILE_ON_AC=high
RADEON_POWER_PROFILE_ON_BAT=low
 
# WiFi power saving mode: 1=disable/5=enable
# (Kernel >= 2.6.32, some adapters only!)
WIFI_PWR_ON_AC=1
WIFI_PWR_ON_BAT=5
 
# Disable wake on lan: Y/N
WOL_DISABLE=Y
 
# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
# A value of 0 disables / >=1 enables power save.
SOUND_POWER_SAVE=1
# Disable controller too (HDA only): Y/N
SOUND_POWER_SAVE_CONTROLLER=Y

# Set to 1 to power off optical drive in UltraBay (ThinkPads only) 
# when running on battery. A value of 0 disables this Feature (Default).
# Drive can be powered on again by releasing (and reinserting) the
# eject lever or by pressing the disc eject button on newer models.
# Note: an UltraBay hard disk is never powered off.
BAY_POWEROFF_ON_BAT=0
# Optical drive device to power off (default sr0)
BAY_DEVICE="sr0"
 
# Runtime Power Management for pci(e) bus devices 
# (Kernel >= 2.6.35 only): on=disable/auto=enable
RUNTIME_PM_ON_AC=on
RUNTIME_PM_ON_BAT=auto

# Set to 0 to disable/1 to enable usb autosuspend feature
USB_AUTOSUSPEND=1
 
# Devices from the following list are excluded from usb autosuspend
# (separate with spaces). Use lsusb to get the id's.
# Note: input devices (usbhid) are excluded automatically
#USB_BLACKLIST="1111:2222 3333:4444"

# Restore radio device state (bluetooth, wifi, wwan) from previous shutdown
# on system startup: 0=disable/1=enable
# Hint: the parameters DEVICES_TO_DISABLE_ON_STARTUP/SHUTDOWN below
#       are ignored when this is enabled!
RESTORE_DEVICE_STATE_ON_STARTUP=0
 
# Radio devices to disable on startup: bluetooth wifi wwan
#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan"
 
# Radio devices to disable on shutdown: bluetooth wifi wwan
# (workaround for devices that are blocking shutdown)
#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
 
# Battery charge thresholds (ThinkPad only, tp-smapi kernel module required)
# Charging starts when the remaining capacity falls below the START_CHARGE_TRESH
# value and stops when exceeding the STOP_CHARGE_TRESH value.
# Main battery (values in %)
#START_CHARGE_THRESH_BAT0=75
#STOP_CHARGE_THRESH_BAT0=80
# Ultrabay battery (values in %)
#START_CHARGE_THRESH_BAT1=75
#STOP_CHARGE_THRESH_BAT1=80

# ------------------------------------------------------------------------------
# tlp-rdw - Parameters for the radio device wizard
# Possible devices: bluetooth/wifi/wwan

# Hint: parameters are disabled by default, remove the leading # to enable them

# Radio devices to disable on connect 
#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"

# Radio devices to enable on disconnect 
#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""

# Radio devices to enable/disable when docked
#DEVICES_TO_ENABLE_ON_DOCK=""
#DEVICES_TO_DISABLE_ON_DOCK=""

# Radio devices to enable/disable when undocked
#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
#DEVICES_TO_DISABLE_ON_UNDOCK=""

